tutorials:make:el-wings
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
tutorials:make:el-wings [2011/10/25 17:51] daigo [What you'll need!] |
tutorials:make:el-wings [2016/01/28 18:05] (current) |
||
|---|---|---|---|
| Line 28: | Line 28: | ||
| ==== What you'll need! ==== | ==== What you'll need! ==== | ||
| - | * ~5m of EL wire, copper tape and driver(s). I used two [[#|Adafruit Aqua EL wire starter kits]].Each pack comes with 2.5 meters, splicing parts like copper tape and heat shrink, and an inverter | + | * ~5m of EL wire, copper tape and driver(s). I used two [[http://www.adafruit.com/products/320|Adafruit Aqua EL wire starter kits]].Each pack comes with 2.5 meters, splicing parts like copper tape and heat shrink, and an inverter |
| * AA batteries to run the inverters | * AA batteries to run the inverters | ||
| * 4 x 12" x 18" craft foam sheets (2mm thickness) - you'll want in two white and in two black - available at any craft or stationary shop | * 4 x 12" x 18" craft foam sheets (2mm thickness) - you'll want in two white and in two black - available at any craft or stationary shop | ||
| Line 37: | Line 37: | ||
| * Heat shrink tubing (at least two 1" sections need to be white)- you can get this at a hardware store or use the heat shrink in the start packs | * Heat shrink tubing (at least two 1" sections need to be white)- you can get this at a hardware store or use the heat shrink in the start packs | ||
| ==== You'll also need tools... ==== | ==== You'll also need tools... ==== | ||
| - | <li>[[http://www.adafruit.com/category/8|Basic soldering gear ]]([[http://www.adafruit.com/products/180|soldering iron]], [[http://www.adafruit.com/products/145|solder]], [[http://www.adafruit.com/products/150|damp sponge]], etc)**you will need to cut & solder the EL wire!**<li>[[http://www.adafruit.com/products/147|Wire stripper]]<li>Scissors<li>A work surface you don't mind getting glue on - cardboard works well<li>Acetone-based nail polish remover for cleaning up any glue mishaps | + | * [[http://www.adafruit.com/category/8|Basic soldering gear ]]([[http://www.adafruit.com/products/180|soldering iron]], [[http://www.adafruit.com/products/145|solder]], [[http://www.adafruit.com/products/150|damp sponge]], etc)**you will need to cut & solder the EL wire!** |
| + | * [[http://www.adafruit.com/products/147|Wire stripper]] | ||
| + | * Scissors | ||
| + | * A work surface you don't mind getting glue on - cardboard works well | ||
| + | * Acetone-based nail polish remover for cleaning up any glue mishaps | ||
| ==== Cutting the craft foam ==== | ==== Cutting the craft foam ==== | ||
| {{ http://www.ladyada.net/images/elwings/01_pattern.jpg?nolink&640x478 |}} | {{ http://www.ladyada.net/images/elwings/01_pattern.jpg?nolink&640x478 |}} | ||
/home/ladyada/public_html/wiki/data/attic/tutorials/make/el-wings.1319565111.txt.gz · Last modified: 2016/01/28 18:05 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
