lpc1343
Differences
This shows you the differences between two versions of the page.
|
lpc1343 [2010/09/08 20:00] ladyada |
lpc1343 [2016/01/28 18:05] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | Testing out the LPC1343 board | ||
| - | ====== Installing the toolchain ====== | ||
| - | |||
| - | Installed YAGARTO according to MicroBuilder's tutorial | ||
| - | http://www.microbuilder.eu/Projects/LPC1343ReferenceDesign/LPC1343Toolchain.aspx | ||
| - | |||
| - | All good! | ||
| - | |||
| - | ====== Install IDE ====== | ||
| - | |||
| - | Go to http://www.codelite.org/ for download | ||
| - | I didn't install UnitTest++ | ||
| - | |||
| - | Also downloaded the CodeBase | ||
| - | http://www.microbuilder.eu/Projects/LPC1343ReferenceDesign/LPC1343CodeBase.aspx | ||
| - | |||
| - | Followed the Codelite tutorial | ||
| - | http://www.microbuilder.eu/Projects/LPC1343ReferenceDesign/LPC1343CodeLiteTutorial.aspx | ||
| - | |||
| - | Open Main.c in the **root** directory under the Workspace tab | ||
| - | |||
| - | Right-clicked on **LPC1343_CodeBase** and selected **Build** | ||
| - | |||
| - | <file> | ||
| - | ----------Build Started-------- | ||
| - | MESSAGE: Entering directory `C:\Documents and Settings\ladyada\My Documents\Projects\lpc1343\LPC1343_CodeBase _v0.30\build\codelite\/../../' | ||
| - | C:\WINDOWS\system32\cmd.exe /c ""mingw32-make.exe" -j 2 -f "LPC1343_CodeBase.mk"" | ||
| - | ----------Building project:[ LPC1343_CodeBase - Debug ]---------- | ||
| - | make[1]: Entering directory `C:/Documents and Settings/ladyada/My Documents/Projects/lpc1343/LPC1343_CodeBase _v0.30' | ||
| - | arm-none-eabi-gcc -c -Os -I. -Wall -mthumb -ffunction-sections -fdata-sections -fmessage-length=0 -mcpu=cortex-m3 -DTARGET=LPC13xx -fno-builtin -o main.o main.c | ||
| - | arm-none-eabi-gcc -nostartfiles -mthumb -Wl,--gc-sections -T lpc1xxx/memory.ld -o firmware.elf main.o chb.o chb_buf.o chb_drvr.o chb_eeprom.o chb_spi.o mcp24aa.o lm75b.o ILI9325.o drawing.o smallfonts.o consolas9.o consolas11.o consolas16.o ff.o mmc.o adc.o cpu.o cmd.o gpio.o i2c.o pmu.o ssp.o systick.o timer16.o timer32.o uart.o uart_buf.o usbconfig.o usbhid.o stdio.o string.o wdt.o commands.o cdcuser.o usbcore.o usbdesc.o usbhw.o usbuser.o sysinit.o LPC13xx_handlers.o LPC1xxx_startup.o | ||
| - | |||
| - | arm-none-eabi-size firmware.elf | ||
| - | text data bss dec hex filename | ||
| - | 10224 116 602 10942 2abe firmware.elf | ||
| - | |||
| - | arm-none-eabi-objcopy --strip-unneeded -O binary firmware.elf firmware.bin | ||
| - | arm-none-eabi-objcopy --strip-unneeded -O ihex firmware.elf firmware.hex | ||
| - | make[1]: Leaving directory `C:/Documents and Settings/ladyada/My Documents/Projects/lpc1343/LPC1343_CodeBase _v0.30' | ||
| - | Executing Post Build commands ... | ||
| - | succesfully updated crc to: efff1abc | ||
| - | Done | ||
| - | ----------Build Ended---------- | ||
| - | 0 errors, 0 warnings | ||
| - | </file> | ||
| - | |||
| - | That didnt actually work. Went into **projectconfig.h** and commented out **#define CFG_INTERFACE** did a Clean & Build. File is now about 3Kb. LED blinks! Hooray! | ||
| - | |||
| - | Don't make the same mistakes I did, always do a Clean before Build!!! | ||
| - | |||
| - | ====== Adding USB CDC ====== | ||
| - | Now to add some basic printing capability! | ||
| - | |||
| - | <code> | ||
| - | int main (void) | ||
| - | { | ||
| - | // Configure cpu and mandatory peripherals | ||
| - | systemInit(); | ||
| - | |||
| - | while (1) | ||
| - | { | ||
| - | #ifdef CFG_INTERFACE | ||
| - | // Handle any incoming command line input | ||
| - | cmdPoll(); | ||
| - | #else | ||
| - | // Toggle LED @ 1 Hz | ||
| - | systickDelay(1000); | ||
| - | if (gpioGetValue(CFG_LED_PORT, CFG_LED_PIN)) | ||
| - | gpioSetValue (CFG_LED_PORT, CFG_LED_PIN, CFG_LED_ON); | ||
| - | else | ||
| - | gpioSetValue (CFG_LED_PORT, CFG_LED_PIN, CFG_LED_OFF); | ||
| - | |||
| - | // Say Hello to my little friend! | ||
| - | printf("hello World!\n\r"); | ||
| - | |||
| - | #endif | ||
| - | } | ||
| - | } | ||
| - | </code> | ||
| - | |||
| - | Do a build and upload the firmware. Connect using a Terminal program at 115.2kbps | ||
| - | |||
| - | {{:lpchello.gif|}} | ||
| - | |||
| - | You'll see a message every second when the LED changes state | ||
| - | |||
| - | ====== Adding analog ====== | ||
| - | |||
| - | You can read from the ADC converter (it can do up to 200ksps) quite easily! | ||
| - | |||
| - | <code> | ||
| - | #include "sysinit.h" | ||
| - | #include "core/adc/adc.h" | ||
| - | |||
| - | int main (void) | ||
| - | { | ||
| - | // Configure cpu and mandatory peripherals | ||
| - | systemInit(); | ||
| - | |||
| - | // initialize the internal ADC | ||
| - | adcInit(); | ||
| - | |||
| - | while (1) | ||
| - | { | ||
| - | #ifdef CFG_INTERFACE | ||
| - | // Handle any incoming command line input | ||
| - | cmdPoll(); | ||
| - | #else | ||
| - | // Toggle LED @ 1 Hz | ||
| - | systickDelay(1000); | ||
| - | if (gpioGetValue(CFG_LED_PORT, CFG_LED_PIN)) | ||
| - | gpioSetValue (CFG_LED_PORT, CFG_LED_PIN, CFG_LED_ON); | ||
| - | else | ||
| - | gpioSetValue (CFG_LED_PORT, CFG_LED_PIN, CFG_LED_OFF); | ||
| - | |||
| - | // Say Hello to my little friend! | ||
| - | printf("Analog 0: %d\n\r", adcRead(0)); | ||
| - | |||
| - | #endif | ||
| - | } | ||
| - | } | ||
| - | </code> | ||
| - | |||
| - | {{:analog0-pot.gif|}} | ||
/home/ladyada/public_html/wiki/data/pages/lpc1343.txt · Last modified: 2016/01/28 18:05 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
