mdcpickandplace:diytray
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
mdcpickandplace:diytray [2010/10/12 01:05] ladyada |
mdcpickandplace:diytray [2016/01/28 18:05] (current) |
||
|---|---|---|---|
| Line 6: | Line 6: | ||
| - | * [[http://www.mcmaster.com/itm/find.asp?searchstring=5537T104 | 20mm Extrusion 2 ft piece]] (McMaster #5537T104) x **2 pieces** | + | * [[http://www.mcmaster.com/#5537T104 | 20mm Extrusion 2 ft piece]] (McMaster #5537T104) x **2 pieces** |
| - | * [[http://www.mcmaster.com/itm/find.asp?searchstring=5537T154|20mm Extrusion T-nuts]] (McMaster #5537T154) x **4 bags of 4** | + | * [[http://www.mcmaster.com/#5537T154|20mm Extrusion T-nuts]] (McMaster #5537T154) x **4 bags of 4** |
| - | * [[http://www.mcmaster.com/itm/find.asp?searchstring=92137A412|Flange Button Head Cap Screw, M5 Size, 8 mm Length, 0.80 mm Pitch]] (McMaster #92137A412) x **1 bag** | + | * [[http://www.mcmaster.com/#92137A412|Flange Button Head Cap Screw, M5 Size, 8 mm Length, 0.80 mm Pitch]] (McMaster #92137A412) x **1 bag** |
| - | * [[http://www.mcmaster.com/itm/find.asp?searchstring=5537T181|20mm Extrusion 90 Degree Bracket, Single, 2-Hole]] (McMaster #537T181) x **4 pieces** | + | * [[http://www.mcmaster.com/#5537T181|20mm Extrusion 90 Degree Bracket, Single, 2-Hole]] (McMaster #537T181) x **4 pieces** |
| - | * [[http://www.mcmaster.com/itm/find.asp?searchstring=5537T14|20mm Extrusion endcap]] (Mcmaster #537T14) x **4 pieces** | + | * [[http://www.mcmaster.com/#5537T14|20mm Extrusion endcap]] (Mcmaster #537T14) x **4 pieces** |
| - | * [[http://www.mcmaster.com/itm/find.asp?searchstring=8560K172&sesnextrep=343409141868956|Clear Cast Acrylic Sheet, .060" Thick, 12" X 24"]] (Mcmaster #8560K172) x **1 piece** | + | * [[http://www.mcmaster.com/#8560K172&sesnextrep=343409141868956|Clear Cast Acrylic Sheet, .060" Thick, 12" X 24"]] (Mcmaster #8560K172) x **1 piece** |
| Total is $50 | Total is $50 | ||
| Line 19: | Line 19: | ||
| Cut the 20mm extrusion into ~18" pieces (make them a little shorter than the pick and place drawer. | Cut the 20mm extrusion into ~18" pieces (make them a little shorter than the pick and place drawer. | ||
| - | Attach the pieces with L-brackets so that the L-brackets face each other on the inside of the holder and the outside right edge is flush with the drawer. | + | Attach the pieces with L-brackets so that the L-brackets face each other on the inside of the holder and the outside right edge is flush with the drawer. Keep the left side loose for later adjustment |
| + | Cut two rails from 1/16" material with 5mm drill holes so that the top edge doesnt rise above the JEDEC tray thickness | ||
| + | |||
| + | Attach the rails with T-slot nuts. | ||
| + | |||
| + | Place the tray on the holder, slide the left side in and tighten. | ||
/home/ladyada/public_html/wiki/data/attic/mdcpickandplace/diytray.1286845526.txt.gz · Last modified: 2016/01/28 18:05 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
