Differences

This shows you the differences between two versions of the page.

--- wavebubble:wave_bubble_2010 [2010/12/05 15:50]
mictronics
+++ wavebubble:wave_bubble_2010 [2016/01/28 18:05] (current)
@@ Line 32: / Line 32: @@
 \\
 == Download Design Files ==
-Schematic:\\
+Schematic: {{:wavebubble:wb2010-usb_batt_schematic.pdf|}}\\
-{{:wavebubble:wb2010-usb_batt_schematic.pdf|}}\\
 \\
-PCB Layout:\\
+PCB Layout: {{:wavebubble:wave_bubble-usb_batt_ltc1730.zip|}}\\
-{{:wavebubble:wave_bubble-usb_batt_ltc1730.zip|}}\\
+Gerber files (see .Info):
 \\
 Target Viewer - Required to open the PCB layout files:\\
@@ Line 44: / Line 43: @@
 ^Name	^Value			^Package		^DIGIKEY ^
 |BAT1	|LiPo 3.7V/1800mAh	|BATTERY		 |
-|C1	|100n			|1206		|399-1249-1-ND	|
+|C1	|.10 uF, 50V			|1206		|399-1249-1-ND	|
-|C2	|100n			|1206		|399-1249-1-ND	|
+|C2	|.10 uF, 50V			|1206		|399-1249-1-ND	|
-|C3	|100n			|1206		|399-1249-1-ND	|
+|C3	|.10 uF, 50V			|1206		|399-1249-1-ND	|
-|C4	|100n			|1206		|399-1249-1-ND	|
+|C4	|.10 uF, 50V			|1206		|399-1249-1-ND	|
-|C5	|1u			|1206		|490-1832-1-ND	|
+|C5	|1uF, 25V			|1206		|490-1832-1-ND	|
-|C6	|220u/6.3V		|SMD_R8X5,4_ELKO	|493-2156-1-ND	|
+|C6	|220uF, 6.3V		|SMD_R8X5,4_ELKO	|493-2156-1-ND	|
-|C7	|47u/6.3V		|SMD_R5X5,4_ELKO	|493-2086-1-ND	|
+|C7	|47uF, 6.3V		|SMD_R5X5,4_ELKO	|493-2086-1-ND	|
 |C8	|1u			|1206		|490-1832-1-ND	|
 |C9	|47n			|1206		|399-1246-1-ND	|
@@ Line 82: / Line 81: @@
 Board size is 77mmx52mmx10mm\\
 \\
-Top layer:\\
+Top layer (Prototype Rev. 2a):\\
+{{:wavebubble:wb2010_main_top.jpg?640x480}}
 \\
-Bottom layer:\\
+Bottom layer (Prototype Rev. 2a):\\
+{{:wavebubble:wb2010_main_bottom.jpg?640x480}}
 \\
 == Download Design Files ==
-Schematic:\\
+Schematic (Rev. 2b): {{:wavebubble:wb2010-main_schematic.pdf|}}
 \\
-PCB Layout:\\
+PCB Layout (Rev. 2b): {{:wavebubble:wave_bubble-main_new_power_switch_v2.zip|}}\\
+Gerber files (see .Info):
 \\
 Target Viewer - Required to open the PCB layout files:\\
@@ Line 103: / Line 105: @@
 |1	|C12	|470p	|1206	|399-1213-1-ND	|
 |1	|C13	|100u/10V	|6032	|495-1528-1-ND	|
-|1	|C18	|22u/35V	|7243	|495-1582-1-ND	|
+|1	|C18	|22u/35V	|7243	|495-1583-1-ND	|
 |1	|C20	|68u/16V	|6032	|478-1774-1-ND	|
 |4	|C23,C24,C29,C30	|4.7u	|1206	|399-1262-1-ND	|
@@ Line 110: / Line 112: @@
 |2	|C41,C44	|1000p	|0603	|399-1082-1-ND	|
 |3	|C43,C53,C54	|22p	|0603	|399-1053-1-ND	|
-|4	|C56,C57,C58,C63	|10n	|0603	|490-1563-1-ND	|
+|4	|C56,C57,C58,C63	|10n	|0603	|478-1254-1-ND	|
 |1	|C59	|100n	|0603	|490-1524-1-ND	|
 |1	|C60	|1u	|0603	|445-1322-1-ND	|
@@ Line 127: / Line 129: @@
 |1	|IC12	|MIC2506YM	|SOIC-8	|576-1084-ND	|
 |1	|IC13	|LMX2433	|TSSOP20	|	|
-|1	|IC14	|LP2985AIM5-2.5CT	|SOT23/5	|LP2985AIM5-2.5CT-ND	|
+|1	|IC14	|LP2985AIM5-2.5CT	|SOT23/5	|LP2985AIM5-2.5/NOPBCT-ND	|
 |1	|JP1	|USB/Batt Board	|1X04	|SAM1029-50-ND	|
 |1	|JP2	|ISP	|2X03-90	|SAM1049-50-ND	|
@@ Line 156: / Line 158: @@
 |1	|R41	|120	|0603	|RHM120GCT-ND	|
 |2	|R43,R45	|22	|0603	|RHM22GCT-ND	|
-|1	|R44	|47	|0603	|RHM47GCT.ND	|
+|1	|R44	|47	|0603	|RHM47GCT-ND	|
 |1	|R46	|100	|1206	|311-100ERCT-ND	|
 |2	|R47,R48	|100K	|1206	|311-100KERCT-ND	|
@@ Line 168: / Line 170: @@
 |1	|X1	|10MHz	|ABMM Crystal	|535-9150-1-ND	|
 \\
+Digikey BOM ID: 22247
+== Errata ==
+Rev. 2b
+   * Nothing to report so far.
+== Hints & Testing ==
+Wavebubble2010 Firmware for hardware tests: {{:wavebubble:wb2010_hardware_test.zip|}}\\
+The ZIP contains the sourcecode and a precompiled .hex file for the ATmega168V.\\
+\\
+Flash the .hex file using a AVR programmer of your choice. Set the ATmega168V fuses as shown below.\\
+\\
+Fuses settings for the AVR ATmega168V in AVR-Studio:{{:wavebubble:avr_fusesettings.jpg}}\\
+\\
+To run the tests connect the Wavebubble2010 via USB and open a terminal programm. Set the terminal to 19200Baud 8N1.\\
+Rest should be self explaining. Type characters to run tests from the menu.

AdaWiki

User Tools

Site Tools

Differences

Page Tools