wavebubble:errata
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
wavebubble:errata [2007/11/23 12:41] bushing |
wavebubble:errata [2011/07/28 04:42] lcstyle |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| Unfortunately, there are many errors or discrepancies between the various resources available for this project. Eventually, they will all be listed here; if you can then update one of the resources (schematic, PCB layout, assembly directions), please do so and then remove the error from this list. | Unfortunately, there are many errors or discrepancies between the various resources available for this project. Eventually, they will all be listed here; if you can then update one of the resources (schematic, PCB layout, assembly directions), please do so and then remove the error from this list. | ||
| - | ===== Forum threads: ===== | + | Note: This errate does not apply to the WB 2010 design by Mictronics found here: http://ladyada.net/wiki/wavebubble/wave_bubble_2010 |
| - | (extract info from thread, place on this page and remove thread from list:) | + | |
| - | + | ||
| - | * http://www.ladyada.net/forums/viewtopic.php?t=4125 | + | |
| - | * http://www.ladyada.net/forums/viewtopic.php?t=4029 | + | |
| - | * http://www.ladyada.net/forums/viewtopic.php?t=4006 | + | |
| - | * http://www.ladyada.net/forums/viewtopic.php?t=3677 | + | |
| - | * http://www.ladyada.net/forums/viewtopic.php?t=3409 | + | |
| - | * http://www.ladyada.net/forums/viewtopic.php?t=3225 | + | |
| - | * http://www.ladyada.net/forums/viewtopic.php?t=3179 | + | |
| ===== Part changes: ===== | ===== Part changes: ===== | ||
| + | ==== Battery board ==== | ||
| + | ^ Part ^ Incorrect ^ Correct ^ Remarks ^ | ||
| + | | R2 | 2K, 0.25W | 500-1000 ohm | The lower the resistance, the brighter the power LED -- can be any wattage | | ||
| + | | R3 | ? | do not place | unused | | ||
| + | | R4 | ? | do not place | unused | | ||
| + | | R5 | ? | do not place | unused | | ||
| + | | Q2 | ? | do not place | unused | | ||
| + | | D1 | ? | SS14 | | ||
| + | | J2 | optional | | If you omit this part, you have to jumper two pads together or else you won't get power from the USB port | | ||
| + | |||
| + | ==== Main (radio) board ==== | ||
| ^ Part ^ Incorrect ^ Correct ^ Remarks ^ | ^ Part ^ Incorrect ^ Correct ^ Remarks ^ | ||
| | C20 | 160pF, do not place | 390-550pF, placement recommended. | | | C20 | 160pF, do not place | 390-550pF, placement recommended. | | ||
| + | | C36 | .47uF | do not place | part of (unused) noise circuit; do not place | | ||
| | C40 | 68pF | ? | Sirenza datasheets say 1-2pF, not clear if this is an error or not | | | C40 | 68pF | ? | Sirenza datasheets say 1-2pF, not clear if this is an error or not | | ||
| | C50 | ? | 1 uF 1206 | | | C50 | ? | 1 uF 1206 | | ||
| Line 21: | Line 23: | ||
| | C52 | ? | 1 uF 1206 | | | C52 | ? | 1 uF 1206 | | ||
| | C53 | ? | .1 uF 1206 | | | C53 | ? | .1 uF 1206 | | ||
| + | | C62 | 0pF | do not place | | ||
| | C63 | ? | 1pF 0603 | | | C63 | ? | 1pF 0603 | | ||
| - | | C77 | ? | 4.7uF or 1uF, 0603 | Filter cap; 4.7uF part is difficult to get in 0603, 1uF is ok | | + | | C77 | ? | 4.7uF or 1uF, 0603 | Power supply filter cap; 4.7uF part is difficult to get in 0603, 1uF is ok | |
| | C80 | 20pF | 22pF | Substitute to save money by combining order with other 22pF caps | | | C80 | 20pF | 22pF | Substitute to save money by combining order with other 22pF caps | | ||
| | C81 | 20pF | 22pF | Substitute to save money by combining order with other 22pF caps | | | C81 | 20pF | 22pF | Substitute to save money by combining order with other 22pF caps | | ||
| - | | C83 | ? | .1uF ? | not listed in instructions | | + | | C83 | .1uF | .1uF ? | on top/parallel R41 | |
| - | | C84 | ? | .1uF ? | not listed in instructions | | + | | C84 | .1uF | .1uF ? | on top/parallel R43 | |
| + | | D1 | 1N5817 | SS14 | | ||
| + | | D2 | 1N5817 | SS14 | | ||
| + | | D3 | 1N5817 | SS14 | | ||
| + | | D4 | 1N5235 | do not place | part of (unused) noise circuit; do not place | | ||
| + | | D5 | 1N5817 | SS14 | optional | | ||
| + | | D6 | 1N5817 | SS14 | optional | | ||
| | IC2 | LM2733X | LM2731Y | Either part will work, but the 33X is not recommended for supplies less than 16v | | | IC2 | LM2733X | LM2731Y | Either part will work, but the 33X is not recommended for supplies less than 16v | | ||
| | L1 | 15 uH | 7.3 uH | Only change if using LM2731Y | | | L1 | 15 uH | 7.3 uH | Only change if using LM2731Y | | ||
| | L5 | ? | 1K resistor | | | L5 | ? | 1K resistor | | ||
| | L6 | ? | 1K resistor | | | L6 | ? | 1K resistor | | ||
| + | | R1 | 510K | ? | Pick a low-voltage point (e.g. 3.7v) -- this voltage divider should | | ||
| + | | R2 | 220K | ? | should output 1.1v at that point. Not currently implemented in firmware. | | ||
| | R3 | ? | 39K | | | R3 | ? | 39K | | ||
| | R4 | ? | 12K | | | R4 | ? | 12K | | ||
| Line 38: | Line 49: | ||
| | R13 | 100K | 63K | Value may vary to adjust VCO DC Offset gain | | | R13 | 100K | 63K | Value may vary to adjust VCO DC Offset gain | | ||
| | R15 | 100K | 33K | Value may vary to adjust VCO DC Offset gain | | | R15 | 100K | 33K | Value may vary to adjust VCO DC Offset gain | | ||
| + | | R19 | 2K | do not place | part of (unused) noise circuit; do not place | | ||
| | R27 | 0 ohms | ferrite bead | | | R27 | 0 ohms | ferrite bead | | ||
| | R28 | 0 ohms | ferrite bead | | | R28 | 0 ohms | ferrite bead | | ||
| + | | R31 | 0 ohms | do not place | | ||
| + | | R90 | 100K | do not place | part of (unused) noise circuit; do not place | | ||
| ===== Misc ===== | ===== Misc ===== | ||
| The silkscreened part numbers for the tiled Gerbers are incorrect; see http://www.ladyada.net/forums/viewtopic.php?t=4143 for more info. | The silkscreened part numbers for the tiled Gerbers are incorrect; see http://www.ladyada.net/forums/viewtopic.php?t=4143 for more info. | ||
/home/ladyada/public_html/wiki/data/pages/wavebubble/errata.txt · Last modified: 2016/01/28 18:05 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
